Annetta, TX metal roofs, formed and installed by PMRS
Standing Seam and Metal Roofs for Annetta Homes, Barns and Shops
Annetta’s zoning ordinance names metal outright. Among the predominant roof finishes it lists for houses, alongside slate and tile, is non-reflective raised seam metal, and it expects those roofs to be pitched between 8:12 and 12:12. Permanent Metal Roofing Systems installs that kind of roof, snap lock and mechanical lock standing seam, along with metal shakes, stone-coated steel and PBR or corrugated panels for barns and shops. Annetta is in Parker County, about 71 miles from our Mesquite office and at the western edge of the area we serve, so our office books estimate visits here ahead of time and plans each installation around the drive. The panels and trim are formed by PMRS and installed by our own crew.
- 20+ years of experience
- Lifetime limited warranty
- Free written estimates
Roof Types We See Around Annetta
Annetta began in the mid-1870s around a station and general store built by a Mr. Fraser, who named the place for his daughter. Today it is a town of homesites rather than tract lots: the R-1 and agricultural districts set a two-acre minimum. The Census puts the median year built at 1999 and owner-occupancy at 96 percent. Town construction standards call for house walls that are at least 80 percent brick or stone, and many houses share their acreage with a shop, a barn or a pool house. Many houses built in the 1980s and 1990s have already had one shingle replacement, and steep pitches make every tear-off a bigger job. A standing seam roof, done once and done properly, ends that cycle.
We work along FM 5, Old Annetta Road and Muir Ranch Road, and on the edges Annetta shares with Annetta North, Annetta South and Aledo.
Annetta Hail, Wind and Heat: What a Roof Faces
Big hail has reached the Annetta area in recent seasons. On the evening of April 28, 2026, broadcast media reported 1.75-inch hail in Annetta South, along the town’s southern edge, the same night a trained spotter reported 4.5-inch stones on Highway 171 between Cresson and Godley. On March 2, 2023, winds estimated at 80 mph snapped six-inch branches in Annetta North, and a ham radio operator measured 68 mph on I-30 at the Tarrant-Parker county line. Against hail, 24-gauge standing seam or a shake profile its maker rates Class 4 under UL 2218 is the sound choice. Against wind on a steep roof, the concealed clips go in at closer spacing along eaves, rakes and the ridge. How much an impact rating saves on a policy is the carrier’s decision.
- Impact-rated standing seam, stone-coated steel and metal shingle options
- Heavier 24-gauge panels that resist cosmetic hail dents better than thinner steel
- Clip spacing and fastening planned for Texas wind uplift
See how Class 4 impact-rated metal roofing works, what to do about hail damage and insurance claims, or compare standing seam systems and stone-coated steel.
Roof Systems for Annetta Homes and Buildings
Standing seam leads in Annetta because the town names it and because steep 8:12-to-12:12 roofs show off long, unbroken panels. We run 1.75-inch snap lock or 1.5-inch mechanical lock in low-gloss PVDF colors so the finish stays non-reflective, as the ordinance asks. Shops, barns and equipment sheds take PBR or corrugated panels, each cut to fit its run. Owners who want texture can choose a metal shake or stone-coated steel; the town may treat those as alternative materials, so we ask before ordering. Copper, as standing seam or diamond panels, finishes a cupola, an entry or a bay window, and our crews bend every ridge cap and flashing to the panel color.
Standing Seam Roofs
A clean, modern roof with no exposed screws to back out, available with Class 4 impact-rated assemblies.
Stone-Coated Steel
A textured, low-glare metal roof that blends into established streets and passes most HOA design reviews.
Metal Shingles and Shakes
Interlocking metal shingles that shed hail and wind and keep a cedar, slate or tile appearance.
Corrugated and PBR Roofs
Corrugated and PBR panels for homes, shops, barns, carports and porches around Annetta.
Copper and Zinc Roofing
Copper accents over a porch or bay window, or a full zinc roof that weathers to a soft gray.
Metal Roof Repair
Loose fasteners, failed sealant and storm-damaged panels repaired or replaced one section at a time.
How much will it cost? That depends on size, pitch, profile, metal and tear-off, so we measure first. Our cost guide walks through the seven factors.
Premium Metal Roofing for Annetta Custom Homes
Most Annetta homes are custom masonry houses on large lots, many of two acres or more, and the land often works as hard as the house: a shop for equipment, a barn for horses, sometimes a covered arena or a pool cabana. Zoning allows up to two horses per full acre on R-1 and R-E parcels of at least two acres. The house roof has to meet the town’s pitch and finish rules, and an accessory building over 600 square feet needs a special exception from the Board of Adjustment, which can require its roof to match the house in pitch and color. Barns and bona fide agricultural buildings in the R-AG, R-E and R-1 districts are exempt from those matching rules. We help owners plan one color story across every roof on the property, with standing seam over the living space and PBR over the stalls.
- Choose a low-gloss, non-reflective finish for the house so the roof stays inside the town’s standard.
- Confirm whether your shop or barn counts as a bona fide agricultural building before ordering panels.
- Apply early for a special exception when an accessory building will exceed 600 square feet.
- Read your recorded deed restrictions for roof material or color terms on top of town zoning.
Compare copper and zinc roofing, architectural standing seam and the warranties that come with each system.
Getting a Metal Roof Approved in Annetta
Annetta’s roofing rules come mainly from the town rather than an HOA. The current zoning ordinance, Ordinance 215 as amended through May 2026, calls for pitched house roofs between 8:12 and 12:12, names slate, concrete or clay tile and non-reflective raised seam metal as the predominant finishes, permits heavyweight architectural shingles, and sends other materials or lower pitches to a special exception. Applications go to the town with a contractor registry form; Bureau Veritas handles plan review and inspections, and every permit needs a passing final. Because the town says not every required permit is listed, we confirm what your re-roof needs before ordering. Recorded deed restrictions can add roof terms of their own, and where an HOA exists, Property Code 202.011 still applies.
Annetta Coverage Snapshot
| Counties | Parker County |
| Residents | Roughly 3,500 |
| Typical home | median value $483,000; half built in 1999 or earlier (Census ACS 2020-2024) |
| From our base | About 71 miles from Mesquite |
| Roof systems | Standing seam, metal shingles and shakes, stone-coated steel, corrugated and PBR, copper and zinc |
| Services | New roofs, replacements, repairs and hail damage documentation |
| Estimate and warranty | Free, measured and itemized in writing; lifetime non-prorated limited warranty on PMRS standing seam, transferable one time |
The PMRS Difference in Annetta
- Your deductible stays your deductible. Texas law bars roofers from covering it, and we comply.
- HOA approval packages with product sheets and color samples.
- Metal roofing specialists since 2006, with our own crews on every job.
- Panels and trim formed by PMRS in Mesquite or on site, so every piece fits the roof it was made for.
- Written, itemized estimates that spell out panel, gauge, finish, underlayment and trim.
What Annetta Owners Ask About Metal Roofs
Is Annetta too far west for PMRS to take on our roof?
No. Annetta sits at the western edge of the area we serve, so our office books estimate visits in advance and sets install dates with the drive in mind. Once a roof is approved, we form the panels at our Mesquite shop or with the roll former trailered to your property, and our own crew installs them. Interstate 30, which crosses Mesquite, ends near Aledo, so the route is a direct one.
Does Annetta’s zoning allow a standing seam roof on our house?
Yes, in the form the ordinance describes. Non-reflective raised seam metal is one of the predominant finishes named for single-family homes, on a pitch between 8:12 and 12:12. A roof that switches to a material outside that list, or drops below 8:12, needs a special exception. We confirm the details with the town before ordering and choose a low-gloss finish so the panels read as non-reflective.
Can our horse barn have a different roof from the house?
Usually. Annetta’s zoning exempts barns and bona fide agricultural buildings in the R-AG, R-E and R-1 districts from the rules that make accessory buildings match the house in texture, pitch and color. Other large accessory buildings, such as a shop or guest house over 600 square feet, go through a special exception, and the Board of Adjustment can ask for a matching roof. We check which category your building falls into first.
Our home is in Annetta North or Annetta South. Do the same rules apply?
Not necessarily. Annetta North and Annetta South are separate incorporated towns with their own councils and ordinances, and Annetta South states that it is not affiliated with the Town of Annetta. Aledo addresses are common across all three, so the mailing address alone does not tell you which rules govern your roof. We look up the jurisdiction for your parcel and follow that town’s permit and zoning requirements.
Does PMRS repair metal roofs in Annetta that another company installed?
Yes. We trace leaks at seams, screws, pipe boots and flashing on standing seam, PBR, corrugated and metal shingle roofs, whoever put them on, and explain the cause before we fix it.
More Cities Near Annetta
- Fort Worth (19 mi)
- Burleson (22 mi)
- North Richland Hills (28 mi)
- Keller (29 mi)
- Arlington (31 mi)
- Mansfield (31 mi)
The full list lives on our DFW service areas page, and the office details are on our Mesquite location page.
Price a Metal Roof for Your Annetta Property
A Annetta estimate costs nothing and comes itemized, with straight answers on panel profile, color and timing.